The portable ultrasonic flowmeter uses the propagation time difference method to measure the volume flow in the pipe from outside the pipe.

Using the latest electronic technology and digital signal processing technology, the product has achieved a qualitative leap in small weight, while the function and operability are also greatly improved.

The new display surface design improves display visibility, the reliability of connector connectors and the enrichment of options.

Characteristic point

1. Small and lightweight

Using the latest electronic technology and digital signal processing technology, the volume of the converter is only 30% of the original and the weight is reduced by 30% compared with the previous products of the company.

2. Battery working mode

The built-in battery can work continuously for 12 hours.

The battery is fast-charging and can be recharged in 3 hours using the included power adapter.

3. Complete range of sensors

Can meet the small diameter to large diameter (tube inner diameter f13~f6000mm),

Low temperature fluids to high temperature fluids (-40~+200°C) and other requirements.

4. High accuracy, high speed response

The accuracy is extremely high, with an accuracy of ±1.0%. Depending on the probe selected, the test conditions will vary.

The response speed is less than 1 second.

5. Improved anti-bubble ability

Using digital signal processing, the anti-bubble ability has been greatly improved.

6. Excellent operability and ease of use

Large color LCD display that is easy to distinguish even outside, few buttons, menu selection method, simple setting.

Waterproof protection structure (only when powered by built-in battery), can also be used in the rain.

7. SD memory card has large recording capacity

The measurement data can be saved to SD memory card at a fixed period. For example, the optional 512MB memory card can store about 2 years of measurement data (save period is 30 seconds, save 14 kinds of data) with a maximum available capacity of 8GB.

8. Serial communication

With the USB port, the connection to the computer is very easy.

It is equipped with computer loading software (standard) to collect measurement data and display and change parameters (address setting).

9. Heat measurement

Heat measurement is possible through temperature input. Simple energy management for cooling and heating.

10. Graphic Printer connection (optional)

Integrated printer for easy recording

11. Flow rate distribution display (optional)

Confirmation before purchase

When this flowmeter meets the following conditions, it will cause the measurement to be impossible or the measurement accuracy to be reduced. If it is difficult to determine whether it is suitable, you can confirm the object device in advance, please contact us. 15901759876 same wechat number

1) Fluid

· Containing a large number of bubbles (standard value: less than 12vol% at a flow rate of 1m/s)

· The turbidity of the fluid is not less than 10000 (mg/L)

· Liquids containing mud or solid substances (standard value is 5wt%)

Low Reynolds number does not exceed 10000 flow

(Reference: the flow rate is 5m3/h at 100mm) ※ The flow rate is proportional to the diameter

· Circulating oil, low concentration liquid medicine, waste liquid, hot spring water, etc

2) Piping

· Carbon steel pipe with rusty and rough inner surface.

· Piping with attachments or deposits on the inner surface.

· Cast iron pipe with rough outer surface.

· Thick resin piping

(PP material: not less than 15mm, PVDF material: not less than 9mm)

· SGPW pipe [galvanized water pipe replacement (commonly known as white coal pipe)]

· Unglued liner (teflon, PVC, glass, etc.)

· Rubber tube

In order to make a correct measurement, it is necessary to know the length of the straight pipe before and after the measurement position. Please meet the conditions for straight pipe as shown on page 1.

Precautions for use

1) Please be careful not to damage the detector and signal cable installed on the distribution pipe.

2) Please always keep the measuring part of the piping full of water.

3) The installation position of the detector during horizontal piping is recommended to be horizontal.

4) When installing the detector outdoors, it is recommended to install a waterproof cover to prevent aging when using grease as a sound coupler.